|
 |
|
 |
OCZ / OCZ DDR Booster Motherboard Compatibility Chart
OCZ DDR Booster Motherboard Compatibility Chart
|
Please refer to the table below to determine motherboard compatibility with OCZ's DDR Booster:
Notes:- Use of the DDR Booster with certain chipsets/motherboards may limit maximum DIMM population.
- VTT mod may be needed to reach above 3.0 VDIMM
- Power supply quality may affect DDR Booster performance and stability.
- DDR Booster power adapter may not fit all Levicom Power Supply models due to Levicom's use of a non-standard ATX adapter.
- Power supplies used in conjunction with the DDR Booster must support a -5V line in order for the LED readout to function.
- The OCZ Booster requires a 20-Pin ATX connector and will not work with power supplies that have 24-Pin connectors
The following notes apply to the DFI NF4 SLI-DR, UT NF4 SLI-D, UT NF4 SLI-DR, UT NF4 Ultra-D and UT NF4-D:- All testing was conducted using the 520w Modstream and all current Powerstream PSU models utilizing the 20+4 pin (split type 24 pin) motherboard connector. The 20 pin section was plugged into the booster and the detachable 4 pin was plugged into the motherboard power connector, giving the required 24 pin connection power supply connection as specified by DFI.
- It is possible to use only the 20 pin connection provided by the DDR Booster and to ignore the additional 4 pins on the motherboard power connector. This however is not approved by DFI and you do so at your own risk.
- Additionally, although our testing has yielded excellent results, OCZ cannot be responsible for any damage that may occur from the use or mis-use of the DDR booster on the DFI boards. Your warranty with DFI may be voided by the use of the DDR Booster.
- In addition, the booster requires a PSU that has a -5v line available at the motherboard power connector. This wire is ?white? according to the ATX specification. If you do not have the -5v line, the booster display will not work and the booster power circuit also may not function properly.
| Manuf. | MOBO | Max.Volt.Tested | Compatible? | |
| | Abit | KV8 | n/a | N | Not Compatible | | Abit | IC7 | 3.6V | Y | Board may need VTT mod for best performance | | Abit | IC7 Max3 | 3.4V | Y | Board may need VTT mod for best performance | | Abit | AN7 | 3.4V | Y | Use in DIMM Slot 3; results in single channel configuration | | Abit | IT7 MAX2 | 2.8V | Y | Does not run above BIOS voltage setting of 2.8V | | Abit | AI7 | 3.4V | Y | | | Abit | NF7 v.2 | 3.4V | Y | Use in DIMM Slot 3; results in single channel configuration | | Abit | NF7S v.2 | 3.4V | Y | Use DIMM slot 3 | | | | Albatron | PX875Pro | n/a | | Not Compatible |
| Albatron | K8NF4X | 3.6 | | |
| ASUS | A7N8X | n/a | N | Functional up to 2.8V. Due to overvolt protection, voltage beyond 2.8V yields precarious results. | | ASUS | A8V | n/a | | Not Compatible | | ASUS | A8N-SLI Deluxe | n/a | | Not Compatible | | ASUS | P4S533 | 3.4V | Y | Will o要ly fit 1 memory module | | ASUS | P4C800-Deluxe | 3.6V | Y | | | ASUS | P4P800 | 3.4V | Y | | | ASUS | P4C800-E | 3.6V | Y | | | ASUS | P4R800-VM | 3.4V | Y | | | ASUS | K8V | 3.4V | Y | Will o要ly run 1 module in slot 2 or 3. | | | | Aopen | AK89max | 3.4V | Y | | | | | Biostar | P4VTB | 3.4V | Y | | | Biostar | K8NHA Pro | 3.4V | Y | | | Biostar | K8VHA PRO | 3.4V | Y | | | | | Chaintech | VNF3-250 | 3.6V | Y | Will only fit one memory module in conjunction with DDR Booster. | | Chaintech | ZNF3-250 | 3.4V | Y | Will o要ly fit o要e memory module in conjunction with Booster. | | Chaintech | ZNF3-150 | 3.4V | Y | | | Chaintech | 9CJS | n/a | N | | | | | DFI | 875LP rev.B | 3.1V | Y | Will not boot above 3.1V. | | DFI | 865PE | 3.4V | Y | | | DFI | nForce2 Lan Party rev B | n/a | N | | | | | DFI | NF4 SLI-DR | 3.8V | Y | | | DFI | UT NF4 SLI-D | 3.8V | Y | | | DFI | UT NF4 SLI-DR | 3.8V | Y | | | DFI | UT NF4 Ultra-D | 3.8V | Y | | | DFI | UT NF4-D | 3.8V | Y | | | Epox | 4PCA3 | n/a | N | Not Compatible | | Epox | 4PCA3I | n/a | N | Not Compatible | | Epox | 8K5A2+ | 3.6V | Y | Use Booster in DIMM slot 2 or 3 | | Epox | 8RDA3+ | 3.4V | Y | Use Booster in DIMM slot 1 or 3. Dual Channel unavailable in conjunction with Booster. | | Epox | 9NDA3+ | n/a | N | Not Compatible | | | | FIC | 875Dynasty | n/a | N | | | FIC | P4M-RJ300 | n/a | N | Not Compatible | | | | Gigabyte | 7N400 Pro 2 | 3.4V | Y | | | Gigabyte | 8KNXP | 3.1V | N | | | Gigabyte | K8NNXP | 3.4V | Y | Can o要ly fit o要e memory module w/o heatspreader | | Gigabyte | K8NSNXP-939 | 3.7V | Y | | | | | Gigabyte | K8NS Ultra-939 | 3.6V | Y | | | | Leadtek | NCR18-D Pro2 Ltd. | n/a | N | | | Leadtek | K7NCR18-D | n/a | N | | | | |
| MSI | 865PE Neo | 3.4V | Y | | | MSI | K8N Neo2 Platinum | 3.4V | Y | | | MSI | 875P Neo | 3.3V | Y | BIOS already adjustable to 3.3V. Will not function reliably beyond this voltage. | | MSI | K8N Neo4 Platinum/SLI | n/a | | Not Compatible | | MSI | K7N2 | 3.3V | Y | Will not boot above 3.3V | | MSI | K8T Neo | 3.4V | Y | Can o要ly fit 1 memory module | | | | MSI | K8N Neo (socket 754) | 3.6V | Y | | | Shuttle | AN50R | n/a | N | | | | | Soltek | Qubic 3801 | 3.8V | Y | Booster will not fit with drive bay cage installed. | | Soltek | SL-865PE | 3.0V | TBD | Will not boost above 3.0V |
|
This compatibility list assumes no modifications are done to the DDR Booster to make it physically fit into a specific motherboard. Any modifications to the DDR Booster will void the Lifetime Warranty. |
|
